Due to the unknown applications individual components may be applied to and installed in, there are no expressed warranties offered to any of these components when purchased separately from a designated listed kit or system which are fully warranted.
These components are included in our Steering Kits as standard equipment but can be purchased separately
#S1BPRESTAGE-1 STEERINGBULLET PROOF ROD END™$99.95ea 3/4" Spherical Teflon lined Heavy-Duty™Bullet Proof Rod Ends™. Designed & manufactured just for use in our Bullet Proof Steering™ and Track Bar Systems™. For rough service high performance off-road steering applications. These are NOT "off the shelf" pieces! Steering Rod End with 3/4-16 RH or LH threads. Gold chromate plated. (specify RH or LH thread)
#S2BPRESTAGE-2 STEERINGBULLET PROOF ROD END™$119.95ea 3/4" Spherical Teflon lined Extreme-Duty™4130 Chromemoly Bullet Proof Rod Ends™. Designed & manufactured just for use in our Bullet Proof Steering™ and Track Bar Systems™. Dedicated specifically for rough service high performance off-road steering applications. These are NOT "off the shelf" pieces! Not recommended for use in suspension applications due to the extreme tightness in a fast moving environment. Steering Rod End with 3/4-16 RH or LH threads. Platinum chromate plated. (LH thread only)
#BPCSBULLET PROOF CLEARANCE SHIM™$16.95 ea. 3/4" (3/16" tall) one-piece machined 1045 Alloy steel clearance shim - zinc plated. These are not merely stamped from a sheet. Allows maximum movement and articulation of our Bullet Proof Rod Ends™. Use on both sides of the rod end. Increases overall articulation on our Bullet Proof Rod Ends™ (from 14 degrees) to 42 degrees. DO NOT STACK THESE SHIMS
#BPRSBULLET PROOF ONE PIECE RETAINER SHIM™$16.95 ea. 3/4" (3/8" tall) one-piece machined 1045 Alloy steel retainer shim - zinc plated. These are not merely stamped from a sheet. Allows maximum movement and articulation of our Bullet Proof rod Ends™ while preventing the rod end from separating in the rare case of failure. Use on the outside mount of the rod end. Increases overall articulation on our Bullet Proof Rod Ends™ (from 14 degrees) to 42 degrees #BPRBBULLET PROOF RISER BUSHING™$13.95ea. 3/4" (5/8" tall) one-piece machined 1045 Alloy steel separator bushing - zinc plated. These are not merely stamped from a sheet. Specifically used as part of the Bullet Proof GM-IFS Steering System™. Use to space rods end up off the knuckle or steering arm for increased clearance. Allows maximum movement and articulation of our Bullet Proof Rod Ends™. Increases overall drag link articulation on our Bullet Proof Rod Ends™ (from 14 deg.) to 42 degrees #BPSBBULLET PROOF SEPARATOR BUSHING™$14.95ea. 3/4" (1/2" tall) one-piece machined 1045 Alloy steel separator bushing - zinc plated. These are not merely stamped from a sheet. Specifically used as part of the Bullet Proof Tie rod Over Knuckle Kit™. Allows maximum movement and articulation of our Bullet Proof Rod Ends™. Use between the tie rod end and the drag link end above the knuckle. Increases overall articulation of the drag link on our Bullet Proof Rod Ends™ (from 14 deg.) to 42 degrees #BPSSBULLET PROOF SPACER SLEEVE™$16.95 ea. 3/4" (7/8" tall) one-piece machined 1045 Alloy steel spacer sleeve - zinc plated. These are not merely stamped from a sheet. Specifically used as part of our Bullet Proof Tack Bar System™. Allows required movement and articulation of our Bullet Proof Rod Ends™. Use between the upper and lower connection points of the track bar ends. Increases overall articulation of the drag link on our Bullet Proof Rod Ends™ (from 14 deg.) to 42 degrees
#BPSNSLOTTED NUT for mounting bolt $3.95 ea. 3/4"-16 RH Slotted grade-5 special production nut - zinc plated. Specifically used as the fastening hardware for our Bullet Proof Steering™ and Track Bar Systems™. Special identification markings on the slots signify the super strong grade-5 rating (most high strength nuts are only grade-2 unless specifically requested and purchased).Slotted for use with cotter pins or safety wire. Extra tall for maximum thread engagement and strength
#BPJNJAM NUT for rod end $2.95 ea. 3/4"-16 RH & LH, super thin jam nut - zinc plated. Specifically used as the locking device for adjusting our Bullet Proof Rod Ends™. Extra thin to take up minimal space for maximum adjustment. Left hand threaded nut is identified by the small indents on the outside of the nut's wrench surface. (please specify RH or LH thread) #F91135BF-911 SHORT MOUNTING BOLT $21.95 ea. 3/4-16 RH x 3.5" long Grade-9 F911® Aerospace bolt(bolt is improved) #F91145BF-911 LONG MOUNTING BOLT -not sold individually- 3/4-16 RH x 4.5" long Grade-9 F911® Aerospace bolt(bolt is improved) #F91150BF-911 LONG MOUNTING BOLT $25.95 ea. 3/4-16 RH x 5" long Grade-9 F911® Aerospace bolt(bolt is improved) #F91160BF-911 LONG MOUNTING BOLT -not sold individually- 3/4-16 RH x 6" long Grade-9 F911® Aerospace bolt(bolt is improved)
THREADED TUBE END INSERT ADAPTER for tubing. 3/4"-16 RH Threaded Tube End Insert Adapter fits into end of tubing and is welded on. (Left hand has a smooth body) #BPTE975R RH Thread for .975" I.D. tube (1.250" O.D.) $18.95 ea. #BPTE985R RH Thread for .985" I.D. tube (1.250" O.D.) $17.95 ea #BPTE103R RH Thread for 1.03" I.D. tube (1.250" O.D.) $17.95 ea #BPTE116R RH Thread for 1.16" I.D. tube (1.375" O.D. )$17.95 ea
THREADED TUBE END INSERT ADAPTER for tubing. 3/4"-16 LH Threaded Tube End Insert Adapter fits into end of tubing and is welded on. Left hand with built in hex for adjustment wrench #BPTE975L LH Thread for .975" I.D. tube no hex head (1.500" O.D.) $19.95 ea #BPTE985L LH Thread for .985" I.D. tube w/hex head (1.250" O.D.)$18.95 ea #BPTE103L LH Thread for 1.03" I.D. tube w/hex head (1.250" O.D.)$18.95 ea #BPTE116L LH Thread for 1.16" I.D. tube w/hex head (1.375" O.D. )$18.95 ea
